Turbine oil can openers

This forum has been developed to discuss maintenance topics in Canada.

Moderators: North Shore, sky's the limit, sepia, Sulako

Post Reply
longjon
Rank 7
Rank 7
Posts: 723
Joined: Mon Mar 20, 2006 7:35 pm

Turbine oil can openers

Post by longjon »

We've known for quite a while that opening the tin (turbine oil) with a metal juice can opener or churchkey, or leatherman or screwdriver is a big no no but this is the first product to address this problem.

How many of you are useing this lil beauty?

www.thecankey.com
---------- ADS -----------
 
User avatar
HS-748 2A
Rank (9)
Rank (9)
Posts: 1125
Joined: Tue Dec 23, 2008 2:39 pm
Location: Rock 101

Re: Turbine oil can openers

Post by HS-748 2A »

Looks like a good plan.

I usually use my Crescent wrench though...
---------- ADS -----------
 
The fastest way to turn money into smoke and noise..
Heliian
Rank (9)
Rank (9)
Posts: 1976
Joined: Wed Apr 29, 2009 2:14 pm

Re: Turbine oil can openers

Post by Heliian »

Maybe i'll get one of those fancy things at some trade show in the future. What i've always used though are my tried and true sidecutters. They are not coated with anything to chip off and using just one jaw, it's pretty easy to put nice little triangular holes right at the edge of the can. When using these lever type openers, the holes end up being a good cm from the edge which spills all over when you're trying to pour just a little bit in a small filler unless you open it up fully and it creates a hole one inch squared which allows more debris in if you're going to use just a little bit of the can at one time. In the future, we won't need metal cans, but until then, sidecutters.

My 2 cents, sorry no change.
---------- ADS -----------
 
iflyforpie
Top Poster
Top Poster
Posts: 8133
Joined: Tue Apr 15, 2008 12:25 pm
Location: Winterfell...

Re: Turbine oil can openers

Post by iflyforpie »

Heliian wrote: In the future, we won't need metal cans, but until then, sidecutters.
That begs the question, why haven't turbine oil manufacturers entered the twentieth century and gone to plastic twist-off bottles?

I am also curious about how many engines have been actually damaged by metal from the oil can or the tool making it past the oil screens or filters. To me seems a bit far fetched.
---------- ADS -----------
 
Geez did I say that....? Or just think it....?
User avatar
dashx
Rank (9)
Rank (9)
Posts: 1227
Joined: Sat Dec 23, 2006 11:51 am

Re: Turbine oil can openers

Post by dashx »

http://www.skygeek.com/turbine-oil-can-opener.html

I too fail to see how the small amount of metal removed from the end of a stainless steel leatherman or a hardened screwdriver could harm an engine but hey anything is possible.

But it certainly (in theory anyway) appears to be a great idea.

It does however beg the question as to how much metal we might have consumed over the years when opening cans of food.....

And why haven't the oil companies gone to using a tab (you know pop cans)? Guinness..........

Does AC synthetic oil break down plastic so fast that it makes plastic unsuitable for long term storage?

And could Starfrit have an alternative to this?

http://www.starfrit.com/Products/kitche ... sc_lang=en

But all joking aside anything that promotes safety should not be ignored.
---------- ADS -----------
 
ahramin
Rank Moderator
Rank Moderator
Posts: 6317
Joined: Tue Feb 17, 2004 5:21 pm
Location: Vancouver

Re: Turbine oil can openers

Post by ahramin »

I'd sure like to see some proof that opening a can with a leatherman or punch type can opener can leave enough metal behind to damage an engine.
---------- ADS -----------
 
Heliian
Rank (9)
Rank (9)
Posts: 1976
Joined: Wed Apr 29, 2009 2:14 pm

Re: Turbine oil can openers

Post by Heliian »

Highly unlikely to damage a turbine as a dry sump system has many devices to keep junk out. The biggest issue I have is that it may show up on the chip detector creating panic for nothing. I can easily tell if the piece came from a can or opener now as i've seen it on more than one occasion.
---------- ADS -----------
 
User avatar
Pat Richard
Rank 8
Rank 8
Posts: 902
Joined: Sat Feb 28, 2004 10:36 pm
Location: all over

Re: Turbine oil can openers

Post by Pat Richard »

I'd sure like to see some proof that opening a can with a leatherman or punch type can opener can leave enough metal behind to damage an engine.
+1, and Im not nerdy enough to "have to have" the latest gizmo some company says important. This reminds me of the whole wave lockwire plier thing.
---------- ADS -----------
 
http://mindflipbooks.ca/
Heliian
Rank (9)
Rank (9)
Posts: 1976
Joined: Wed Apr 29, 2009 2:14 pm

Re: Turbine oil can openers

Post by Heliian »

They make pliers for lockwiring?
---------- ADS -----------
 
DBA
Rank 1
Rank 1
Posts: 33
Joined: Mon Nov 22, 2010 2:30 pm

Re: Turbine oil can openers

Post by DBA »

Heliian wrote:They make pliers for lockwiring?
Surely this is sarcasm?
---------- ADS -----------
 
Saabquatch
Rank 0
Rank 0
Posts: 1
Joined: Sat Nov 13, 2010 9:41 pm

Re: Turbine oil can openers

Post by Saabquatch »

What the hell is lockwire?
---------- ADS -----------
 
benmech1981
Rank 0
Rank 0
Posts: 1
Joined: Thu Dec 15, 2011 2:50 am

Re: Turbine oil can openers

Post by benmech1981 »

I've used the cankey and have always gone back to my trusty metal one as they blunt up quite quickly and make it difficult to open cans, However they dont set off metal detectors at airports so you dont get molested by security everytime you go through! :smt040
---------- ADS -----------
 
Hornblower
Rank 7
Rank 7
Posts: 686
Joined: Sat Jan 08, 2005 6:58 am

Re: Turbine oil can openers

Post by Hornblower »

couple o' pokes with a # 1 phillips
---------- ADS -----------
 
Hornblower
Rank 7
Rank 7
Posts: 686
Joined: Sat Jan 08, 2005 6:58 am

Re: Turbine oil can openers

Post by Hornblower »

#2 if I'm in a hurry
---------- ADS -----------
 
Post Reply

Return to “Maintenance”